myWerkzeug.de › CNC.myWerkzeug.de › Templates › myWerkzeug.de
CNC template · myWerkzeug.de
LED lamp circuit from the Electronics House
Lumi’s lesson as a board: three LEDs in red, yellow and green, each with its own 1 kΩ series resistor on 12 V. That gives about 10 mA per LED. The first board for learning to solder.
- Size
- 60 × 44 mm, 1.6 mm thick
- Material
- Circuit board (FR4)
- Difficulty
- Beginner
- Milling time
- approx. 12 min
- Bits
- Engraving bit 30°, PCB drill Ø 0.8 mm, PCB drill Ø 1.3 mm, Corn cob router bit Ø 2 mm
- Customise
- Fixed template, freely editable once opened
- With a laser
- milling machine only (PCB isolation, a diode laser cannot cut this material)
Free with an account · carve with Chrome or Edge · no installation
Try the circuit first in the Electronics House (German, beta) →
Build instructions
Parts
| Qty | Part | Value | In layout |
|---|---|---|---|
| 3 | Resistor 0.25 W | 1 kΩ Colour bands: brown, black, red, gold | R1, R2, R3 |
| 1 | LED 5 mm The long lead is the anode; the flat side (cathode) points to the mark in the layout. | red | LED1 |
| 1 | LED 5 mm The long lead is the anode; the flat side (cathode) points to the mark in the layout. | yellow | LED2 |
| 1 | LED 5 mm The long lead is the anode; the flat side (cathode) points to the mark in the layout. | green | LED3 |
| 1 | Screw terminal 2-pin, 5.08 mm pitch | X1 |
You also need: soldering iron (about 30 W, fine tip), 0.5 to 1 mm solder with flux, side cutters and a multimeter.
Assembly
- Mill the board: isolate the copper first, then drill, and finally mill out the holes and the outline. The order is shown in the Milling panel.
- Cut through the holding tabs, deburr the edges and rub the copper bright with a scouring pad. After that, do not touch the copper side with your fingers.
- Use a magnifier and a continuity tester to look for leftover copper between neighbouring traces; cut any bridges with a craft knife.
- Insert the parts from the side without copper and solder them on the copper side. Fit low parts first: resistors and diodes, then sockets and transistors, and finally capacitors, terminals and large parts.
- Before soldering, compare the polarity with the component layout: band of the diodes, flat side of the LEDs, minus stripe of the electrolytic capacitors, notch of the ICs.
- Solder each lead for about two seconds at around 330 °C: tip on pad and lead, feed solder until it flows all round. Then clip the leads just above the joint.
- Solder the three resistors R1 to R3, then the LEDs with the flat side towards the mark, and the terminal X1 last.
- Visual check: no solder bridges, no dull, balled-up joints. Remove flux residue with isopropyl alcohol and an old toothbrush.
Test and power up
- Before switching on for the first time, check with the meter that there is no short between plus and minus of the supply. Power up the first time on a bench supply with current limiting if possible.
- Apply 12 V DC to X1 (plus to +): all three LEDs light up.
- If an LED stays dark, it is usually soldered in the wrong way round. Measure: the resistor drops about 10 V, which means 10 mA.
- Finally protect the copper side against oxidation with solder lacquer or plastic spray.
How to carve this template
- OpenOpen the template in the app and adjust size and text if you like.
- CheckLook at it in 3D, check run time and warnings.
- Set upThe carve wizard guides you through material, clamping, bit and zero point.
- CarvePress start; the app drives your Grbl router directly over USB.
